|
|
|
|
產品[
風機專用潤滑油DRESSER
]資料
如果您對該產品感興趣的話,可以
產品名稱:
風機專用潤滑油DRESSER
產品型號:
Synthetic Oil
產品展商:
其它品牌
簡單介紹
風機專用潤滑油DRESSER合成齒輪油推薦用于很寬的溫度范圍、要求很長的換油周期并且是高溫下的軸承和齒輪。特別推薦用于工業封閉齒輪的潤滑、“密封以延長壽命”的系統中、滑動軸承和滾柱軸承。風機專用潤滑油DRESSER也被推薦用于惰輪浸漬系統、強制滴油和機械噴霧系統。在正常的噴霧系統中，可以保持輪齒表面的全覆蓋。在從礦物齒輪油轉換到本系列合成齒輪油時，無需清洗設備。
風機專用潤滑油DRESSER的詳細介紹
|
|
ISO Grade/AGMA Grade
|
|
Typical Properties*
|
100
|
150***
|
220
|
320
|
|
AGMA Grade
|
3
|
4
|
5
|
6
|
|
Viscosity
cSt @ 40°C cSt @ 100°C SSU @ 100°C SSU @ 210°C
|
100
12.6
518
70
|
150
16.1
783
84
|
220
21.5
1153
108
|
320
27.0
1685
139
|
|
Viscosity Index
|
120
|
112
|
117
|
112
|
|
Specific Gravity @ 60°F
|
0.863
|
0.869
|
0.874
|
0.880
|
|
Lbs./Gal
|
7.19
|
7.24
|
7.28
|
7.33
|
|
Flash °F
|
440
|
485
|
485
|
500
|
|
Pour Point °F
|
-53
|
-47
|
-35
|
-35
|
|
ISO Cleanliness Level
|
NA
|
NA
|
NA
|
NA
|
|
ASTM D-1401 Demulsibility
(from 40/40/0/06 to 40/40/0/30)
|
Pass
|
Pass
|
Pass
|
Pass
|
|
D-892 Foam Tests Sequences I, II & III
|
—
|
—
|
—
|
—
|
|
D-130 Copper Corrosion
3 hrs. @ 210°F
250 hrs. @ 210°F
|
1A
1A
|
1A
1A
|
1A
1A
|
1A
1A
|
|
Cincinnati Millicron “A”
72 hrs. @ 275°F
|
Pass
|
Pass
|
Pass
|
Pass
|
|
D-665 Rust Test Fresh Water Salt Water
|
Pass Pass
|
Pass Pass
|
Pass Pass
|
Pass Pass
|
|
D-2893 Dry Air Oxidation
312 hrs. @ 203°F,
% Viscosity Increase Precip. No. (% Solids)
|
0
0
|
0
0
|
0
0
|
0
0
|
  *All properties are typical and may vary.
Note:
ROOTS Synthetic Oil’s solvency cleans wear metals and deposits left behind by previous oils. These wear metals and deposits can become soluble in the new oil, causing abnormally high values on used oil analysis until equipment is clean.
Note:
ROOTS Synthetic Oil is NSF approved for ISO-VG 32, 150, 220 and 320.
Specified lubricants
|
2"-8" Blower Recommended Oil Grades
|
|
Ambient Temperature
|
ISO Viscosity Range
|
|
Above 90°F (32°C)
|
320
|
|
32° to 90°F (0°-32°C)
|
220
|
|
0° to 32°F (-18°-0°C)
|
150
|
|
Below 0°F (-18°C)
|
100
|
|
10"-20" Splash Lubricated Blower Recommended Lubricating Oils
|
|
Ambient Temperature
|
ISO Viscosity Range
|
|
Above 90°F (32°C)
|
320
|
|
32° to 90°F (0°-32°C)
|
220
|
|
0° to 32°F (-18°-0°C)
|
150
|
|
Below 0°F (-18°C)
|
100
|
|
10"-20" Pressure Lubricated Blower Recommended Lubricating Oils
|
|
Ambient Temperature
|
ISO Viscosity Range
|
|
32° to 120°F (0°-49°C)
|
220
|
|
Below 32°F (0°C)
|
100
|
All RGS - Use ISO-VG-100
See the manual provided with the blower for service intervals of the lubrications mentioned.
|
|
